modellbau:planes:1-2-fun
created: 2021/05 mod:2021/09
Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
| Beide Seiten der vorigen RevisionVorhergehende ÜberarbeitungNächste Überarbeitung | Vorhergehende Überarbeitung | ||
| modellbau:planes:1-2-fun [2021/06/22] – hermenj | modellbau:planes:1-2-fun [2021/09/28] (aktuell) – hermenj | ||
|---|---|---|---|
| Zeile 4: | Zeile 4: | ||
| < | < | ||
| - | {{ : | + | {{ : |
| < | < | ||
| * Motor Dist.: 80/95mm | * Motor Dist.: 80/95mm | ||
| * Motor Dist. Diag: 125mm | * Motor Dist. Diag: 125mm | ||
| - | * Weight: 72g, 120g with 1S18650, 104g with 2S550mAh | + | * Weight: |
| - | * Flightcontroller: | + | * Flightcontroller: |
| * Motors: 4x [[bg> | * Motors: 4x [[bg> | ||
| - | * ESCs: [[bg> | ||
| * RX: [[bg> | * RX: [[bg> | ||
| - | * Battery: | + | * Battery: |
| * Frame: CFK/Foam Sandwich modified from [[https:// | * Frame: CFK/Foam Sandwich modified from [[https:// | ||
| - | * FPV: [[bg> | + | * FPV: <del>[[bg> |
| * FlightTime: | * FlightTime: | ||
| </ | </ | ||
| Zeile 25: | Zeile 24: | ||
| I slightly modified eyeflys Sting frame to fit a whoop-style controller and a smaller cam. I added a printed holder for a 18650 Cell inside the frame that features an additional XT30 connector for the 2S Lipo. | I slightly modified eyeflys Sting frame to fit a whoop-style controller and a smaller cam. I added a printed holder for a 18650 Cell inside the frame that features an additional XT30 connector for the 2S Lipo. | ||
| + | Modified this one to run on 2S Only but carying a naked Caddx Vista Nebula Nano v2. Added some Ducts for indoor use. | ||
| ===== Pics: ===== | ===== Pics: ===== | ||
| Zeile 41: | Zeile 40: | ||
| ===== Settings: ===== | ===== Settings: ===== | ||
| - | JHEMCU Play F4 AIRB/NOX(STM32F411) | + | Use [[https:// |
| - | + | < | |
| - | orig: | + | # diff all |
| - | | + | |
| - | | + | # version |
| - | | + | # Betaflight |
| - | | + | # config: manufacturer_id: |
| - | + | ||
| - | | + | # start the command batch |
| - | resource LED_STRIP 1 none | + | batch start |
| - | resource SERIAL_TX 11 none | + | |
| - | resource SERIAL_RX 11 none | + | # reset configuration to default settings |
| - | | + | defaults nosave |
| - | save | + | |
| - | + | board_name MATEKF411 | |
| - | set report_cell_voltage = ON | + | manufacturer_id MTKS |
| - | save | + | mcu_id 002b00523235511832333634 |
| - | + | signature | |
| - | # vtxtable Eachine Nano V3 VTX | + | |
| - | | + | # name: dragonfrog |
| - | | + | |
| - | | + | # resources |
| - | | + | resource SERVO 1 A00 |
| - | | + | resource LED_STRIP 1 NONE |
| - | | + | resource SERIAL_TX 11 A08 |
| - | | + | resource SERIAL_RX 11 A08 |
| - | | + | |
| - | | + | # serial |
| - | vtxtable powerlabels 25 100 200 400 | + | serial 0 1 115200 57600 0 115200 |
| - | | + | serial 1 64 115200 57600 0 115200 |
| + | serial 30 2 115200 57600 0 115200 | ||
| + | |||
| + | # aux | ||
| + | aux 0 0 0 1700 2100 0 0 | ||
| + | aux 1 1 1 900 1300 0 0 | ||
| + | aux 2 2 1 1300 1700 0 0 | ||
| + | aux 3 13 3 1700 2100 0 0 | ||
| + | |||
| + | # master | ||
| + | set acc_calibration = 42, | ||
| + | set rssi_channel = 16 | ||
| + | set serialrx_provider = CRSF | ||
| + | set failsafe_switch_mode = STAGE2 | ||
| + | set bat_capacity = 850 | ||
| + | set vbat_scale = 112 | ||
| + | set ibata_scale = 309 | ||
| + | set gps_auto_config = OFF | ||
| + | set gps_rescue_min_sats = 5 | ||
| + | set gps_rescue_allow_arming_without_fix = ON | ||
| + | set report_cell_voltage = ON | ||
| + | set osd_warn_rssi = ON | ||
| + | set osd_warn_dji = ON | ||
| + | set osd_cap_alarm = 800 | ||
| + | set osd_vbat_pos = 2419 | ||
| + | set osd_rssi_pos = 2197 | ||
| + | set osd_link_quality_pos = 121 | ||
| + | set osd_rssi_dbm_pos = 89 | ||
| + | set osd_tim_2_pos = 407 | ||
| + | set osd_flymode_pos = 2183 | ||
| + | set osd_vtx_channel_pos = 65 | ||
| + | set osd_crosshairs_pos = 2286 | ||
| + | set osd_current_pos = 2374 | ||
| + | set osd_mah_drawn_pos = 2406 | ||
| + | set osd_craft_name_pos = 2224 | ||
| + | set osd_warnings_pos = 14794 | ||
| + | set osd_avg_cell_voltage_pos = 2387 | ||
| + | set osd_stat_max_spd = OFF | ||
| + | set osd_stat_bbox = OFF | ||
| + | set osd_stat_bb_no = OFF | ||
| + | set gyro_1_align_yaw = 1800 | ||
| + | set name = dragonfrog | ||
| + | |||
| + | profile 0 | ||
| + | |||
| + | profile 1 | ||
| + | |||
| + | profile 2 | ||
| + | |||
| + | # restore original profile selection | ||
| + | profile 0 | ||
| + | |||
| + | rateprofile 0 | ||
| + | |||
| + | rateprofile | ||
| + | |||
| + | rateprofile | ||
| + | |||
| + | rateprofile | ||
| + | |||
| + | rateprofile | ||
| + | |||
| + | rateprofile | ||
| + | |||
| + | # restore original rateprofile selection | ||
| + | rateprofile 0 | ||
| + | # save configuration | ||
| + | save | ||
| + | </ | ||
Ich garantiere bei meinen Bauberichten und Teilelisten keine Vollständigkeit etc...es wird aus den Teilen gebastelt die gerade herumliegen.
Bitte keine Anfragen zum Bau/Fräsen von Frames, Teilen oder sonstigen Aufträgen. Ich betreibe die Seite rein als Hobby und nutze die zur Verfügung stehende Zeit gerne für meine eigenen Projekte.
Bei einigen Projekten werde ich zu gegebener Zeit die Pläne veröffentlichen - aber auch hier lasse ich mich ungern hetzten ;-)
No waranties for completeness of any contructions, part lists etc.. I build from party i have just lying around in my workshop.
Please, No requests to buy frames, builds, etc.. I run this page in my spare-time and as hobby only. Want to keep my free time to work on my own projects - sorry
I will release the plans for some build at some point in time, but again, please don't ask for unreleased plans, i don't want to get rushed ;-)
modellbau/planes/1-2-fun.1624338401.txt.gz · Zuletzt geändert: 2021/06/22 von hermenj
Seiten-Werkzeuge
Falls nicht anders bezeichnet, ist der Inhalt dieses Wikis unter der folgenden Lizenz veröffentlicht: CC Attribution-Noncommercial-Share Alike 4.0 International
