created: 2021/05 mod:2022/03

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- modellbau:planes:3inch_1404 [2021/09/27] – [Settings:] hermenj
+++ modellbau:planes:3inch_1404 [2022/03/10] (aktuell) – hermenj
@@ Zeile 2: / Zeile 2: @@
 <columns>
-{{ :modellbau:planes:3inch_1404:3inch_1404_013.jpg?direct500&direct| }}
+{{ :modellbau:planes:3inch_1404:3inch_1404_021.jpg?direct500&direct| }}
 <newcolumn>
     * Motor Dist.: 85mm
@@ Zeile 11: / Zeile 11: @@
     * RX: [[bg>https://www.banggood.com/0_42g-Happymodel-2_4G-ExpressLRS-EP1-Nano-High-Refresh-Rate-Ultra-small-Long-Range-RC-Receiver-for-RC-Drone-p-1835181.html|Happymodel EP1 eLRS Receiver]]
     * Battery:  [[https://chinahobbyline.com/shop/detail/15|CNHL MiniStar 850mAh 11.1V 3S 70C]]
-    * Frame: 2.5mm CFK modified from [[https://www.thingiverse.com/thing:3647138]]
+    * Frame: 3mm/2.5mm CFK modified from [[https://www.thingiverse.com/thing:3647138]]
     * FPV: [[bg>Caddx-Nebula-Nano-Kit-Vista-HD-Digital-System-5_8GHz-FPV-Transmitter-VTX+2_1mm-150-Degree-720P-60fps-FPV-Camera-AIO-for-DJI-Digital-Unit-Googles-p-1680064.html|Caddx Nebula Nano v2 Kit Vista HD]]
     * FlightTime:
@@ Zeile 37: / Zeile 37: @@
 ===== Settings: =====
+Use [[https://github.com/mbilozub/fpv_custom_mods/tree/master/mods/dji-warning/betaflight|Custom Betaflight]] for BF warnings on DJI OSD
+Settings for the GHF13 Board
 <code>
-diff all
+#
+# diff all
 # version
 # Betaflight / STM32F411 (S411) 4.2.8 Mar 19 2021 / 21:01:25 (norevision) MSP API: 1.43
-# config: manufacturer_id: MTKS, board_name: MATEKF411, version: 7b156dec, date: 2021-07-26T13:19:23Z
+# config: manufacturer_id: MTKS, board_name: MATEKF411, version: be0c9205, date: 2020-01-15T19:44:32Z
 # start the command batch
@@ Zeile 52: / Zeile 57: @@
 board_name MATEKF411
 manufacturer_id MTKS
-mcu_id 0053002e3237511135393337
+mcu_id 004e00523235511832333634
 signature
+# name: dragonfrog
 # resources
-resource MOTOR 1 B06
+resource SERVO 1 A00
-resource MOTOR 2 B07
+resource LED_STRIP 1 NONE
-resource MOTOR 3 B04
+resource SERIAL_TX 11 A08
-resource MOTOR 4 B05
+resource SERIAL_RX 11 A08
-# mixer
-mixer Y4
-# feature
-feature LED_STRIP
 # serial
 serial 0 1 115200 57600 0 115200
 serial 1 64 115200 57600 0 115200
+serial 30 2 115200 57600 0 115200
-# led
-led 0 7,0::CTW:1
-led 1 8,0::CTW:1
-# color
-color 0 216,0,255
-color 1 294,0,255
-# mode_color
-mode_color 7 0 5
 # aux
@@ Zeile 89: / Zeile 80: @@
 # master
-set acc_calibration = -31,75,-80,1
+set acc_calibration = 1,-9,-105,1
 set rssi_channel = 16
 set serialrx_provider = CRSF
-set align_board_roll = 180
+set failsafe_switch_mode = STAGE2
-set small_angle = 180
+set bat_capacity = 850
+set vbat_scale = 112
+set ibata_scale = 309
+set gps_auto_config = OFF
+set gps_rescue_min_sats = 5
+set gps_rescue_allow_arming_without_fix = ON
 set report_cell_voltage = ON
 set osd_warn_rssi = ON
 set osd_warn_dji = ON
+set osd_cap_alarm = 800
 set osd_vbat_pos = 2419
 set osd_rssi_pos = 2197
@@ Zeile 104: / Zeile 101: @@
 set osd_flymode_pos = 2183
 set osd_vtx_channel_pos = 65
-set osd_crosshairs_pos = 2287
+set osd_crosshairs_pos = 2286
 set osd_current_pos = 2374
 set osd_mah_drawn_pos = 2406
@@ Zeile 114: / Zeile 111: @@
 set osd_stat_bb_no = OFF
 set gyro_1_align_yaw = 1800
+set name = dragonfrog
 profile 0
-# profile 0
-set p_pitch = 38
-set i_pitch = 81
-set d_pitch = 31
-set f_pitch = 86
-set p_roll = 35
-set i_roll = 77
-set d_roll = 29
-set f_roll = 81
-set p_yaw = 35
-set i_yaw = 78
-set f_yaw = 81
-set d_min_roll = 21
-set d_min_pitch = 23
 profile 1
@@ Zeile 140: / Zeile 123: @@
 rateprofile 0
-# rateprofile 0
-set thr_expo = 30
-set roll_srate = 80
-set pitch_srate = 80
-set throttle_limit_type = SCALE
-set throttle_limit_percent = 90
 rateprofile 1

Ich garantiere bei meinen Bauberichten und Teilelisten keine Vollständigkeit etc...es wird aus den Teilen gebastelt die gerade herumliegen.
Bitte keine Anfragen zum Bau/Fräsen von Frames, Teilen oder sonstigen Aufträgen. Ich betreibe die Seite rein als Hobby und nutze die zur Verfügung stehende Zeit gerne für meine eigenen Projekte.
Bei einigen Projekten werde ich zu gegebener Zeit die Pläne veröffentlichen - aber auch hier lasse ich mich ungern hetzten ;-)

No waranties for completeness of any contructions, part lists etc.. I build from party i have just lying around in my workshop.
Please, No requests to buy frames, builds, etc.. I run this page in my spare-time and as hobby only. Want to keep my free time to work on my own projects - sorry
I will release the plans for some build at some point in time, but again, please don't ask for unreleased plans, i don't want to get rushed ;-)

der-frickler.net

Benutzer-Werkzeuge

Webseiten-Werkzeuge

Unterschiede

Seiten-Werkzeuge